fuse types and uses pdf

Fuse types and uses pdf

File Name: fuse types and uses .zip
Size: 26217Kb
Published: 14.04.2021

Different Types of Fuses

DIN-type, HRC-fuse link range

Cartridge fuse

Different Types of Fuses

Many different Fuse-Links, for example in special dimensions, as well as a wide range of accessories round up the portfolio. System The range of PU PG Sur. Ag Sur. Holder 1 HH 3 75,50 Test device for tripping device. They protect apparatus and equipment against the thermal and dynamic effects of short-circuits.

A fuse is probably the simplest electrical device, but its function is critical in protecting electrical circuits from damage. Fuses are found in every circuit in one form or another in various shapes, sizes, and ratings. In this article, we will learn how a fuse works and about the different types of the fuse. The primary job of a fuse is to break the circuit if a current higher than desired is drawn by the circuit, thus preventing damage due to short circuits. The simplest kind of fuse consists of a resistive element , selected carefully for its melting point. The temperature of the element thus increases.

Normally, the ampacity rating of a conductor is a circuit design limit never to be intentionally exceeded, but there is an application where ampacity exceedance is expected: in the case of fuses. A fuse is an electrical safety device built around a conductive strip that is designed to melt and separate in the event of excessive current. Fuses are always connected in series with the component s to be protected from overcurrent, so that when the fuse blows opens it will open the entire circuit and stop current through the component s. A fuse connected in one branch of a parallel circuit , of course, would not affect current through any of the other branches. Normally, the thin piece of fuse wire is contained within a safety sheath to minimize hazards of arc blast if the wire burns open with violent force, as can happen in the case of severe overcurrents.

DIN-type, HRC-fuse link range

The fuse is the current interrupting devices which break or open the circuit by fusing the element and thus remove the faulty device from the main supply circuit. The fuses are mainly classified into two types, depends on the input supply voltages they are the AC fuses and the DC fuses. The different types of the fuses are shown in the image below. The DC fuse opens or breaks the circuit when the excessive current flow through it. The only difficulty with the DC fuse is that the arc produced by the direct current is very difficult to extinct because there are no zero current flows in the circuit. For reducing the DC fuse arcing the electrodes are placed more distance apart due to which the size of the fuse increases as compared to AC fuse. The AC fuses are categorised into two types they are the low voltage fuses and the high voltage fuses.

Fuses can be considered as a sacrificial element in the circuit as they act as a weak link in the entire circuit. This is because, a fuse scarifies itself and reliably opens the circuit when there is an excessive current in the circuit or the circuit is under over load and if there is any short circuit. The principle of a fuse is based on the heating effect of the electric current. A simple fuse consists of a small conductive material with low resistance and it is placed in series with the circuit. The cross section area of this conducting material is designed such that it allows a certain amount of current that is permitted to flow in the circuit. When the current in the circuit exceeds this permitted value which may be caused due to overload, short circuit or load mismatch , this excessive current will melt the conductive element in the fuse and opens the circuit. This will disconnect the power supply and thus, the rest of the circuit is protected from being damaged.

Cartridge fuse

Fuses are the protectors, these are the safety devices which are used to protect the home appliances like televisions, refrigerators, computers with damage by high voltage. The fuse is made up of thin strip or strand of metal, whenever the heavy amount of current or an excessive current flow is there in an electrical circuit, the fuse melts and it opens the circuit and disconnects it from the power supply. Also, it works as a circuit breaker or stabilizer which protects the device from damage.

In electronics and electrical engineering , a fuse is an electrical safety device that operates to provide overcurrent protection of an electrical circuit. Its essential component is a metal wire or strip that melts when too much current flows through it, thereby stopping or interrupting the current. It is a sacrificial device ; once a fuse has operated it is an open circuit, and must be replaced or rewired, depending on its type. Fuses have been used as essential safety devices from the early days of electrical engineering.

Electric fuse was invented by Thomas Alva Edison in There are many types of fuses, but the function of all these fuses is the same. In this article, we will discuss the different types of fuses, its construction, working and operation and their application in various electronics and electrical systems.

Fuses and Types of Fuses

Basically, use 3 type of fuse 1. Rewirable or Kit-kat fuse 2. Cartridge fuse 3.

Different Types of Fuses

CART 0. ISO Registered. Term Search:. Fuse type 2. Fuse type 24 Type A 60 volt DC fuse designed for the telecom industry.

Через шестьдесят секунд у него над головой затрещал интерком. - Прошу начальника систем безопасности связаться с главным коммутатором, где его ждет важное сообщение. От изумления у Джаббы глаза вылезли на лоб. Похоже, она от меня не отвяжется. И он решил не реагировать на сообщение.

Fuses and Types of Fuses

 Вы себя хорошо чувствуете? - спросил он, пятясь к двери. - Нормально, - высокомерно бросила.  - А тебе здесь делать нечего.

0 comments

Leave a reply